Posted on December 25, 2018

DELL MONITOR – E151FPB DRIVER DOWNLOAD

It was quite challenging to troubleshoot this kind of problem where you are hundred percent sure that the primary side is giving problem yet you could not find out the culprit. From experienced I do encountered semiconductor components breakdown when under full operating voltage. You could use this method but first you must confirm that the secondary filter capacitors, TL adjustable precision shunt regulator ic, optoisolators and components surrounding the optoisolator is working before you proceed to use the light bulb. Removing the cover was a bit easy compared to other models. Now we could use a 12 volt automobile brake light bulb to test at which section that is causing the low voltage output problem.

Uploader: Kale
Date Added: 17 November 2008
File Size: 54.71 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 56079
Price: Free* [*Free Regsitration Required]

I began to check again the defective 2N fet with my analog meter and peak electronic atlas component analyzer and the result is still the same-tested good!

Guess what, you would not believe what have I just discovered-a defective 2N fet! If the LCD monitor designed to run on 18 or 24 volts then you could use a light bulb from the big trailer. Since I had checked all the components and could not locate the fault, the only way that I could do is to direct replace the semiconductor devices such as the diodes, scr, fet, and transistors.

This is the time to really test your basic electronics skill because you now know at which area the fault is and you just have to use your skills to locate the exact bad component. Removing the cover was a bit easy compared to other models.

New Drivers  V UAS14 XP DRIVER DOWNLOAD

Dell E151FPB LCD Monitor

monitro I could not believe it was this faulty fet that causes all the output voltages to drop! After checking all the components I was surprised that all of them tested okay.

There were not much components in the primary side, and you could easily check all of them in less than 20 minutes.

You could use this method but first you must confirm that the secondary filter capacitors, TL adjustable precision shunt regulator ic, optoisolators and components surrounding the optoisolator is working before you proceed to use the light bulb.

It was quite challenging to troubleshoot this kind of problem where you are hundred percent sure that the primary side is giving problem yet you could not find out the culprit.

As usual whenever the mainboard and power board were exposed, I would look for any bulged capacitor, darkened area, a loosen connector and etc. Hope you enjoy this article and more good articles to come everyday! Removing the fuse as shown in the photo and connect the bulb between the supply line and the cold ground could tell which section is giving problem.

In fact this is good news to us because we know what the next step that we montior make. What you have just learned from here was that if all the suspected components tested good, the only way to reveal the truth is to direct replace the parts.

One by one of the semiconductor components I replaced and power on each time I had changed it to see if the bulb light up or not.

New Drivers  SITECOM CN-523 DRIVER DOWNLOAD

To continue using , please upgrade your browser.

How To Test Electronics Components. From experienced I do encountered semiconductor components breakdown when under full operating voltage.

The moments E511fpb have replaced this fet and power on, the bulb immediately light up. Wishing you all the best and happy repairing! Just like flyback transformer, the best testing equipment to test Fet and other components is actually the equipment itself because it runs on full operating voltage, frequency, signal and etc. However this monitor boards looks perfectly okay.

When the power is on the light bulb still do not lit and the sound still could be heard. Dell Efpb LCD monitor came in with the complaint of no power but upon carefully look at the Dsll you could see a very light blur white flashes across e151fpbb screen and the power LED is not lit.

Now we could use a 12 volt automobile brake light bulb to test at which section that is causing the low voltage output problem. Plasma TV Repair Ebook. A defective component in either primary or secondary side could cause low output voltage. When I measure the 12 volts line with a digital multimeter, mnitor readout was about 7- 8 volts which was very unusual.